China Factory for Water Filter For Drinking Water - MBR Membrane Module Reinforced PVDF BM-SLMBR-20 Sewage Treatment – Bangmo
China Factory for Water Filter For Drinking Water - MBR Membrane Module Reinforced PVDF BM-SLMBR-20 Sewage Treatment – Bangmo Detail:
Product Overview
MBR is a combination of membrane technology and bio-chemical reaction in water treatment. MBR filter the sewage in bio-chemical tank with membrane so that sludge and water are separated. On one hand, membrane rejects microorganisms in the tank, which greatly increase the concentration of activated sludge to a high level, thus the bio-chemical reaction of sewage degradation processes more rapidly and thoroughly. On the other hand, water output is clear and of high quality because of high precision of membrane.
This product adopts reinforced modified PVDF material, which will not peel or break during backwashing, meanwhile it has good permeable rate, mechanical performance, chemical resistance and anti-fouling ability. ID & OD of reinforced hollow fiber membrane are 1.0mm and 2.2mm respectively, filtering precision is 0.1 micron. Filtering direction is outside-in, that is raw water, driven by differential pressure, permeates into the hollow fibers, while bacteria, colloids, suspended solids and microorganisms etc. are rejected in the membrane tank.
Applications
●Treatment, recycle and reuse of industrial waste water;
●Treatment of refuse leachate;
●Upgrade and reuse of municipal sewage.
Filtration Performance
Below filtration effects are proved according to the use of modified PVDF hollow fiber ultrafiltration membrane in different types of water:
| No. | Item | Water Output Index |
| 1 | TSS | ≤1mg/L |
| 2 | Turbidity | ≤1 |
| 3 | CODcr | Removal rate depends on the bio-chemical performance & designed sludge concentration |
| 4 | NH3-H | (Instant removal rate ≤30% without bio-chemical) |
Specifications
Size
Technical Parameters:
| Filtering Direction | Outside-in |
| Membrane Material | Reinforced Modified PVDF |
| Precision | 0.1 micron |
| Membrane Area | 20m2 |
| Membrane ID/OD | 1.0mm/ 2.2mm |
| Size | 785mm×1510mm×40mm |
| Joint Size | DN32 |
Component Material:
| Component | Material |
| Hollow Fiber Membrane | Reinforced Modified PVDF |
| Sealing Compound | Epoxy Resins + Polyurethane (PU) |
| Housing | ABS |
Using Conditions
Proper pretreatments must be set when raw water contains a lot of impurities/coarse particles or large proportion of grease. Defoamer must be used to remove foams in membrane tank when necessary, please use alcoholic defoamer which is not easy to scale.
| Item | Limit | Remark |
| PH Range | 5-9 (2-12 when washing) | Neutral PH is better for bacterial culture |
| Particle Diameter | <2mm | Prevent sharp particles to scratch membrane |
| Oil & Grease | ≤2mg/L | Prevent membrane fouling/sharp flux decrease |
| Hardness | ≤150mg/L | Prevent membrane scaling |
Application Parameters:
| Designed Flux | 10~25L/m2.h |
| Backwashing Flux | Twice the designed flux |
| Operating Temperature | 5~45°C |
| Maximum Operating Pressure | -50KPa |
| Suggested Operating Pressure | ≤-35KPa |
| Maximum backwashing Pressure | 100KPa |
| Operating Mode | Operate 9min & Stop 1min/Operate 8min & Stop 2min |
| Blowing Mode | Continuous Aeration |
| Aeration Rate | 4m3/h.piece |
| Washing Period | Clean water backwashing every 2~4h; CEB every 2~4 days;Offline washing every 6~12 months(Above information is for reference only, please adjustaccording to actual differential pressure change rule) |
Product detail pictures:
Related Product Guide:
continue to enhance, to be certain solution high quality in line with market and buyer standard requirements. Our corporation has a excellent assurance program are actually established for China Factory for Water Filter For Drinking Water - MBR Membrane Module Reinforced PVDF BM-SLMBR-20 Sewage Treatment – Bangmo , The product will supply to all over the world, such as: Southampton , Jakarta , Eindhoven , Our factory is equipped with complete facility in 10000 square meters, which makes us be able to satisfy the producing and sales for auto part solutions. Our advantage is full category, high quality and competitive price! Based on that, our products win a high admiration both at home and abroad.
By Wendy
from UK
- 2018.02.12 14:52
The manufacturer gave us a big discount under the premise of ensuring the quality of products, thank you very much, we will select this company again.
By Henry stokeld
from Karachi
- 2017.03.07 13:42
