Good quality Membrane Filtration Method - UF Membrane Module 6 inch PVDF Ultrafiltration Membrane Module UFf160 Grinding Waste Water Treatment – Bangmo

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

With sophisticated technologies and facilities, strict high quality handle, reasonable value, exceptional support and close co-operation with clients, we are devoted to furnishing the ideal worth for our clients for Ultra Filtration Water Filter , Ultrafiltration Design Calculations , Membrane Water Filter , Our group members are goal to provides merchandise with significant performance cost ratio to our consumers, as well as target for all of us is usually to satisfy our consumers from all around the environment.
Good quality Membrane Filtration Method - UF Membrane Module 6 inch PVDF Ultrafiltration Membrane Module UFf160 Grinding Waste Water Treatment – Bangmo Detail:

Product Overview

UFf160 capillary hollow fiber membrane is high polymer material, which will not have any phase change. Modified PVDF material, which is adopted on this product, has good permeable rate, good mechanical properties, good chemical resistance and pollution resistance. MWCO is 200K Dalton, membrane ID/OD is 0.8mm/1.3mm, filtering type is outside-in.

Applications

  • Drinking water treatment of tap water, surface water, well water and river water.
  • Pretreatment of RO.
  • Treatment, recycle and reuse of industrial waste water.

Filtration Performance

This product is proven to have below filtering effects according to the service conditions of different water sources:

Ingredient Effect
SS, Particles > 1μm Removal Rate ≥ 99%
SDI ≤ 3
Bacteria, Viruses > 4 log
Turbidity < 1NTU
TOC Removal Rate: 0-25%

*Above data is obtained under the condition that feeding water turbidity is < 25NTU.

Product Parameters

product-description110

Technical Parameters:

Filtering Type Outside-in
Membrane Material Modified PVDF
MWCO 200K Dalton
Membrane Area 40m2
Membrane ID/OD 0.8mm/1.3mm
Dimensions Φ160mm*1810mm
Connector Size DN40 Union Joint

Application Data:

Pure Water Flux 8,000L/H (0.15MPa, 25C)
Designed Flux 40-120L/m2.hr (0.15MPa, 25C)
Suggested Working Pressure ≤ 0.2MPa
Maximum Transmembrane Pressure 0.15MPa
Maximum Backwashing Pressure 0.15MPa
Air Washing Volume 0.1-0.15N m3/m2 .hr
Air Washing Pressure ≤ 0.1MPa
Maximum Working Temperature 45C
PH Range Working: 4-10; Washing: 2-12
Operating Mode Cross Flow

Feeding Water Requirements:
Before feeding water, a security filter < 50 μm should be set to prevent blockage caused by large particles in raw water.

Turbidity ≤ 25NTU
Oil & Grease ≤ 2mg/L
SS ≤ 20mg/L
Total Iron ≤ 1mg/L
Continuous Residual Chlorine ≤ 5ppm
COD Suggested ≤ 500mg/L

*Material of UF membrane is polymer organic plastic, there must not be any organic solvents in raw water.

Operating Parameters:

Backwashing Flow Rate 100-150L/m2.hr
Backwashing Frequency Every 30-60min.
Backwashing Duration 30-60s
CEB Frequency 0-4 times per day
CEB Duration 5-10min.
CIP Frequency Every 1-3 months
Washing Chemicals:
Sterilization 15ppm Sodium Hypochlorite
Organic Pollution Washing 0.2% Sodium Hypochlorite + 0.1% Sodium Hydroxide
Inorganic Pollution Washing 1-2% Citric Acid/0.2% Hydrochloric Acid

Component Material:

Component Material
Membrane Modified PVDF
Sealing Epoxy Resins
Housing UPVC

Product detail pictures:

Good quality Membrane Filtration Method -
 UF Membrane Module 6 inch PVDF Ultrafiltration Membrane Module UFf160 Grinding Waste Water Treatment – Bangmo detail pictures

Good quality Membrane Filtration Method -
 UF Membrane Module 6 inch PVDF Ultrafiltration Membrane Module UFf160 Grinding Waste Water Treatment – Bangmo detail pictures


Related Product Guide:

We have been also concentrating on enhancing the things management and QC method so that we could preserve terrific edge inside the fiercely-competitive enterprise for Good quality Membrane Filtration Method - UF Membrane Module 6 inch PVDF Ultrafiltration Membrane Module UFf160 Grinding Waste Water Treatment – Bangmo , The product will supply to all over the world, such as: Norway , Qatar , Czech republic , Based on experienced engineers, all orders for drawing-based or sample-based processing are welcomed. We have won a good reputation for outstanding customer service among our overseas customers. We will continue to try the to offer you good quality products and whole heartedly service. We are looking forward to serving you.
  • In China, we have purchased many times, this time is successful and satisfactory, a sincere and realiable Chinese manufacturer!
    5 Stars By Pearl Permewan from Nigeria - 2017.04.08 14:55
    This company has the idea of better quality, lower processing costs, prices are more reasonable, so they have competitive product quality and price, that's the main reason we chose to cooperate.
    5 Stars By Lisa from Cairo - 2018.12.14 15:26
    Write your message here and send it to us