Popular Design for Mbr Treatment - UF Membrane Module PVC Ultrafiltration Membrane Module UFc50C Stainless Steel Housing Household Water Purification – Bangmo
Popular Design for Mbr Treatment - UF Membrane Module PVC Ultrafiltration Membrane Module UFc50C Stainless Steel Housing Household Water Purification – Bangmo Detail:
Product Overview
UFc50C is capillary hollow fiber membrane made of high polymer material, which is a separating product that will not have any phase change. The modified PVC material adopted to this product has good permeable rate, good mechanical strength, good chemical resistance anti-pollution ability, MWCO is 100k Dalton. Membrane ID/OD is 1.0mm/1.8mm, filtering direction is inside-out, that is raw water flows inside the hollow fibers and, driven by differential pressure, permeates outwards so as to filter bacteria, colloids, suspended substances, microbes, and other harmful substances.
Applications
Production of mineral water, mountain spring water and other germ-free liquid;
Drinking treatment of tap water, surface water, well water and river water;
Pre-treatment of RO device;
Treatment, recycle and reuse of industrial wastewater
Filtration Performance
According to the service conditions of modified PVC hollow fiber ultrafiltration membrane which are applied to various water sources, the product is proved to reach below filtration effects:
| Water Composition | Filtering Effect |
| Suspended Substances, Particles >1um | Removal Rate ≥99% |
| SDI | ≤ 3 |
| Virus, Bacteria | >4 log |
| Turbidity | <0.1NTU |
| TOC | Removal Rate 0-25% |
Above data is obtained when turbidity of feed water is less than 15NTU. The product is proved to reach the sanitary standards of drinking water by Health Department of Guangdong Province. Approval number is YUE WEI SHUI ZI 2014S1671.
Product Parameters
Product Appearance
Figure 1 Product Dimensions
Inner Filter
Figure 2 Inner Filter Dimensions
Technical Parameters:
| Structure | Inside-out |
| Membrane Material | Modified PVC |
| MWCO | 100K Dalton |
| Nominal Membrane Area | 5.4m |
| Membrane ID/OD | 1.0mm/1.8mm |
| Module Dimensions | Φ105mm× 1110mm |
| Connector Dimensions | 3/4” Female Thread |
Application Data:
| Pure Water Flux | 1,700L/H (0.15MPa, 25ºC) |
| Designed Flux | 35-100L/H (0.15MPa, 25ºC) |
| Operating Pressure | ≤0.2MPa |
| Maximum Trans Membrane Pressure | 0.2MPa |
| Maximum Operating Temperature | 45ºC |
| Operating PH Range | 4-10 |
| Washing PH Range | 2-12 |
| Operating Mode | Cross-flow/Dead-end Filtration |
Feed Water Requirements:
A security filter, precision <50 micron, should be set as pretreatment of UF, in case of blockage caused by large particles in raw water. Attention: UF membrane material is macromolecular organic plastics, raw water must not contain any organic solvents.
| Feed Water Turbidity | ≤15NTU |
| Oil & Grease | ≤2mg/L |
| Feed Water SS | ≤20mg/L |
| Total Iron | ≤1mg/L |
| Continuous Feeding Residual Chlorine | ≤5ppm |
| COD | Suggested ≤500mg/L |
Component Material:
| Component | Material |
| Hollow Fiber Membrane | Modified PVC |
| Potting Material | Epoxy Resins |
| Membrane Housing | SUS304 |
Typical Operating Parameters:
| Maximum Backwashing Pressure | 0.2MPa | |
| Backwashing Flow Rate | 100-150L/m2 .h | |
| Backwashing Frequency | Every 30-60 minutes | |
| Backwashing Duration | 30-60 seconds | |
| CEB Frequency | 0-4 times/day | |
| CEB Duration | 5-10 minutes | |
| CIP Frequency | 1-3 months | |
| General Washing Chemicals ： | ||
| Disinfection | 15ppm NaClO | |
| Organic Contamination Washing | 0.2% NaClo+0.1% NaOH | |
| Inorganic Contamination Washing | 1-2% Citric Acid /0.2% HCl | |
Product detail pictures:
Related Product Guide:
As for aggressive costs, we believe that you will be searching far and wide for anything that can beat us. We can state with absolute certainty that for such high-quality at such rates we have been the lowest around for Popular Design for Mbr Treatment - UF Membrane Module PVC Ultrafiltration Membrane Module UFc50C Stainless Steel Housing Household Water Purification – Bangmo , The product will supply to all over the world, such as: Bangalore , Manchester , Malta , Due to the stability of our items, timely supply and our sincere service, we are able to sell our merchandise not only over the domestic market, but also exported to countries and regions, including the Middle East, Asia, Europe and other countries and regions. At the same time, we also undertake OEM and ODM orders. We will do our to serve your company, and establish a successful and friendly cooperation with you.
By Faithe
from Netherlands
- 2017.06.22 12:49
This company has the idea of better quality, lower processing costs, prices are more reasonable, so they have competitive product quality and price, that's the main reason we chose to cooperate.
By Renee
from Puerto Rico
- 2018.11.22 12:28
